Search found 70 matches
- 17 Jun 2022, 16:46
- Forum: Immunity
- Topic: Defining two DVM's for Conducted Immunity Multiband test
- Replies: 0
- Views: 7272
Defining two DVM's for Conducted Immunity Multiband test
We are performing an ED-14 S18 AFCS test. We want to use two DVM's. One DVM for regulating the test level (Voltage close loop method). The second DVM is used for limiting the current in the loop, DVM with current probe Zt = 0.1 ohm (Measured voltage limit). Where can i define the second DVM in the T...
- 29 Oct 2021, 14:01
- Forum: Device drivers
- Topic: Device driver for Microwave analyzer Keysight Fieldfox 9916B
- Replies: 1
- Views: 4778
Device driver for Microwave analyzer Keysight Fieldfox 9916B
We have a Microwave analyzer Keysight Fieldfox 9916B 14 GHz with options: Spectrum Analyzer and Vector Network Analyzer (1-port). Could you make a device driver for both options in Radimation. We want to use this instrument for emission measurements (Spectrum Analyzer mode) and for EUT calibration (...
- 04 Aug 2021, 13:16
- Forum: Report Generator
- Topic: Changing "template word document"
- Replies: 3
- Views: 4209
Re: Changing "template word document"
I found the correct Word document in the "printout" directory. Changed the contents of the document and run again. It works.
- 02 Aug 2021, 14:16
- Forum: Immunity
- Topic: Extra monitoring equipment
- Replies: 2
- Views: 2569
Re: Extra monitoring equipment
Thanks for the information. Still there is something not clear. For current (limit) monitoring we using a current probe together with a voltmeter. The current probe is from the Device Type "Current sensor" in the test setup with a transducer factor of 0.1 Ohm (-20 dBOhm). Where do i have to configur...
- 02 Aug 2021, 11:55
- Forum: Report Generator
- Topic: Changing "template word document"
- Replies: 3
- Views: 4209
Re: Changing "template word document"
Thanks for the information.
Could you tell me which templates in the "printout" directory are used for CE and RE measurements. Otherwise i have to look which templates are used, takes some time to investigate.
Could you tell me which templates in the "printout" directory are used for CE and RE measurements. Otherwise i have to look which templates are used, takes some time to investigate.
- 21 Jul 2021, 14:39
- Forum: Immunity
- Topic: Extra monitoring equipment
- Replies: 2
- Views: 2569
Extra monitoring equipment
We are performing an Conducted Immunity Audio Frequent Test regulating on an (fixed) voltage (Test level = Voltage closed loop method). Besides this we also want to limit at a maximum current measured with an additional current meter or voltage meter (current through a current resistor) in the test ...
- 21 Jul 2021, 14:21
- Forum: Report Generator
- Topic: Changing "template word document"
- Replies: 3
- Views: 4209
Changing "template word document"
We want "to print part of the data from one test" for an RE measurement. To do this you have to select the graph that you want to print and then click the "print graph" button above the graph. The graph that will be printed is referred to a template Word document, probably located in the "printout" ...
- 14 Dec 2020, 12:53
- Forum: Immunity
- Topic: Markers for Conducted Immunity tests
- Replies: 1
- Views: 2548
Markers for Conducted Immunity tests
When doing conducted immunity test according to a frequency list the measured data of the separate frequency points are connected by lines in the graph. Is it also possible in the graph to mark the frequency points (additional) by markers. If Yes, how to do this in Radimation for new and old tests.
- 01 Jul 2020, 16:08
- Forum: Immunity
- Topic: Reverberation chamber in radimation
- Replies: 1
- Views: 2633
Reverberation chamber in radimation
We want to use a reverberation room as alternative method for the MIl-STD-461 RS103/ED-14 S20 Radiated Susceptibility test. Is there a work-around to control the stirror of a reverberation room. Could we use the turntable settings of the turn table for control of the stirror. Are there drivers for t...
- 19 Jun 2020, 12:21
- Forum: Immunity
- Topic: Calibration on voltage level
- Replies: 1
- Views: 2466
Calibration on voltage level
Performing a "Calibration > System Calibration > Conducted Immunity" on a voltage test level. The only measuring instrument i use is a DVM. However, the software asks for sensor power meter a.s.o. How do i have to define this calibration on voltage level?
- 19 Jun 2020, 12:15
- Forum: Immunity
- Topic: Correction file for differential voltage probe
- Replies: 1
- Views: 2389
Correction file for differential voltage probe
Performing a "Conducted Immunity > Multiband > voltage closed loop" test. Using a diff. voltage probe (attn. factor of 10) on the multimeter input. Where can i define the correction factor of 10 for this probe in the "test site". As work around, i define the test level a factor of 10 lower. However,...
- 28 Aug 2019, 15:58
- Forum: Device drivers
- Topic: New device driver for RGN2006B generator
- Replies: 2
- Views: 6724
Re: New device driver for RGN2006B generator
Is there already some information about this item.
As long the two generators are not combined to one new generator this measurement set-up of hardware and software is too time consuming for calibrating several RF components.
As long the two generators are not combined to one new generator this measurement set-up of hardware and software is too time consuming for calibrating several RF components.
- 07 Mar 2019, 17:04
- Forum: Immunity
- Topic: More than one correction file for coupler
- Replies: 1
- Views: 3483
More than one correction file for coupler
Normally you can add only one correction file for the FWD or REV path of a coupler. Is it possible to add more than one correction file in the coupler path. Reason: between coupler and RF power meter we have several RF components, like coax cables and power combiners. We want to correct for all thes...
- 07 Mar 2019, 17:03
- Forum: General
- Topic: More correction files for coupler
- Replies: 7
- Views: 8582
More correction files for coupler
Normally you can add only one correction file for the FWD or REV path of a coupler. Is it possible to add more than one correction file in the coupler path. Reason: between coupler and RF power meter we have several RF components, like coax cables and power combiners. We want to correct for all thes...
- 24 Jan 2019, 17:51
- Forum: Immunity
- Topic: Audio Frequency Conducted Susceptibility test
- Replies: 2
- Views: 5390
Re: Audio Frequency Conducted Susceptibility test
L.s,
Is there already somebody who knows how to setup a MIL-STD-461 CS101 test with power limitation curve of the generator.
Is there already somebody who knows how to setup a MIL-STD-461 CS101 test with power limitation curve of the generator.
- 18 Jan 2019, 17:36
- Forum: Immunity
- Topic: Current Test
- Replies: 0
- Views: 5812
Current Test
We want to perform a current test by injecting a fixed/variabel current through an injection wire over a certain frequency range. Measuring device is (current) series resistor with oscilloscope or DVM. Also the current can be measured with a current clamp.
How to configure this test?
How to configure this test?
- 13 Nov 2018, 13:10
- Forum: Report Generator
- Topic: Keyword for limit line/reference line in graph
- Replies: 1
- Views: 3845
Keyword for limit line/reference line in graph
During an EUT Calibration; Attenuation / Gain test Limit Lines can de defined in the script. What is the keyword for these Limit Lines to plot in a graph in a Word document.
- 13 Nov 2018, 13:04
- Forum: General
- Topic: Limit line/Reference line units
- Replies: 1
- Views: 5360
Limit line/Reference line units
Where can we change the unit of the quantity Frequency. Standard it is defined in kHz. we want to change it to Hz.
- 09 May 2018, 11:38
- Forum: Device drivers
- Topic: Device driver for FSV3 tracking generator
- Replies: 1
- Views: 4187
Device driver for FSV3 tracking generator
We have a tracking generator in our R&S FSV3 spectrum analyzer. We found the R&S ESU tracking generator in the list of generator device drivers but this device driver didn't work for the FSV3.
Could you make a device driver for the FSV3 tracking generator.
Could you make a device driver for the FSV3 tracking generator.
- 25 Apr 2018, 12:55
- Forum: General
- Topic: Synchro of test sites between different user PC's
- Replies: 2
- Views: 5810
Synchro of test sites between different user PC's
Sofar i understand in Radimation has each local PC (PC1) his own "Test sites" configuration (defined in the "ConfDvdr" directory) and is it not possible to synchronise these test sites to an another PC2. The only way to have a copy of this ConfDvdr of PC1 in PC2 is to delete the old one and paste th...