RadiMation forum

It is possible to modify the RadiMation device driver of the Maturo MCU antenna tower controller to NOT perform any height changes. This is however at this moment only possible with an 'advanced' trick. Start RadiMation Go to Configuration > Configuration Select the device drivers tab Select the 'an...

Hi emvlab, RadiMation is very often controlling the antenna tower through an antenna tower controller. That controller is the computer communication interface between the antenna tower itself and the PC. Often the antenna tower controller is connected to the real physical antenna tower through fiber...

It is theoretically correct to configure an attenuator and have RadiMation correct for the 6dB attenuation. However it is not necessary at all, because the same test setup is used during the calibration and the real subtitution test. The 6 dB attenuator is not used for the measurement of an actual v...

In the 'Dok4.docx' file you included a screenshot of the device driver configuration of the R&S ESU8 receiver. That is ok, but that device driver is only controlling the 'emission measurement' part of the R&S ESU8. This device driver is is however not able to control the LISN. The control of the LIS...

It indeed can happen that a connection between two devices is not a single cable, but consists of multiple cables and attenuators. You describe that you are now manually calculating and creating a single correction file that contains the total of all the added individual attenuations of all the sepa...

Have you already been able to resolve the problem with the control of the ENV216 from the ESU8?
We do like to hear the solution, as it can help other users in the future.

I investigated the problem that you reported. However no changes have been made in the device driver that controls the LISN that is connected to the R&S ESU8 for a few years. Also no other end-users have reported a problem related to what you describe. At this moment it thus is difficult to provide ...

It should indeed be possible to control the ENV216 LISN that is connected to the R&S ESU8, by using a RadiMation device driver. At this moment I do not know why it is not working anymore in the 2019.2.5 version. I would expect that it working as you are expecting. We will have to investigate this is...

It is correct that the ||RADIMATION VERSION|| code should normally be replaced with the version of RadiMation that is being used to generate the report. However when a test specific template is used, this code is raising some ambiquity. Each test also records the RadiMation version that is used to p...

The configuration details of the 'Configurable LISN' are documented on the RadiWiki website at: https://wiki.radimation.com/wiki/index.php/Configurable_LISN For a simple LISN that is not automatically controlled it is not necessary to specify any command in any of the textboxes. For a simple (non-co...

Also see https://forum.radimation.com/viewtopic.php?f=6&t=881 , which is a similar question referring to a greyed out VBW and sweep time.

Also see https://forum.radimation.com/viewtopic.php?f=5&t=883 for a very similar question, which also explains the difference between the frequency and time graph.

In the GTEM-Cell, the antenna distance is indeed not really required. It is however important to note and write down, what the actual septum height is at the location where the field probe is positioned during the calibration. The when a substitution is performed using the generated calibration file...

The septum height input field should be filled with the height between the septum and the ground at the location where the EUT is placed. For the correct calculation of the measurement results, this should really be the height at the location of the EUT. It the same EUT is going to be positioned mor...

We have released an updated version of the RadiMation software, which includes several improvements and fixes for problems that have been detected since the release of the 2020.0.11 version. This version 2020.0.12 has been validated by our internal software quality checks. We strongly advise to test...

We have a RadiMation device driver exactly for this. It is the 'Rohde & Schwarz ESU Controlled LISN' device driver, which is one of the LISN device drivers that are available in RadiMation. Please see the documentation of this device driver on our RadiWiki site: https://wiki.radimation.com/wiki/inde...

To be able to represent the actual current flowing through a current sensor, it is indeed important that a device specific calibration factor is linked to the current sensor device driver in RadiMation. The impedance (or resistance) of the current sensor is required in the correct calculation of the...

With some small tips and tricks, it is indeed possible to do the measurements of these similar standards only once. It however does require that some manual interactions are needed, as it is not possible to do it fully automated according to all the standards. As a general description, the following...

It is indeed correct that there could be a difference in the variation in the graph of the same value between the time graph and the frequency graph. The frequency graph shows the value, based on a frequency index. For every unique frequency there is thus only a single value shown. The value that is...

The markers for the final measurement of the average and the quasi peak detectors, are just normal graphs. However those graphs are not included in the graphline index above the graph. Within RadiMation the markers can be shown (or hidden) by clicking on the 'Graphs' button, and then select the 'Pea...