New version: RadiMation version 2015.2.4

This forum contains news and upcoming events regarding RadiMation
Post Reply
User avatar
joro
Posts: 440
Joined: 24 Aug 2011, 09:55
Contact:

New version: RadiMation version 2015.2.4

Post by joro »

We have released a new major version of the RadiMation software, which includes several improvements and small fixes for problems that have been detected since the release of the 2015.1.12 version.
This version 2015.2.4 is the new major version that has been validated at DARE!! Measurements for two weeks. During this two week period no problems have been found. We however strongly advise to test and verify (according to your quality system) this and each new version of RadiMation at for example a separate PC or laptop with your setup and with your measurement equipment, before you are going to use it for daily operation.

The following issues are fixed in this 2015.2.4 version (compared to the 2015.1.12 version):
  • #5954: R&S ESL 6 Scanning Receiver Specific System Error -222 Data out of range SCAN1:TIME 1 MS
  • #6251: R&S ESR7 specific System Error: -222 Data out of Range DISP:TRAC:Y:RLEV:0.0103DBM
  • #6287: Driver: R&S ESL6 as Sensor power meter
  • #6301: Preamplifier setting is not visible anymore in the CE MB TSF window
  • #6303: HP 34401A message There is no Device Stream Configuration
  • #6303: List of performed tests is not updated in the report generator, when a test is finished
  • #6308: COM port setting is not remembered in the RadiMate IV device driver
  • #1864: Move during measurement checkbox is shown in unlogical state if multiple bands are selected.
  • #5320: Folder name is changed to New Directory again
  • #5744: After adding a TSF directory it doesn't show the renamed directory name directly
  • #5894: DARE Homepage menu item name and link is incorrect
  • #5898: Graph items and restore factory default are disabled for the Chart settings
  • #5947: Modulation of Marconi 2024 Signal generator is never turned off during CI test
  • #6202: Show the DeviceStream configuration of a device driver in a panel below a combobox
  • #6243: Communication issue with a RadiSense IV connected by CTR1
  • #6250: Advanced configuration dropdown boxes are not visible for the RadiSense IV driver
  • #6286: Report generation doesn't replace all the codes
  • #703: Calibration Types
  • #1922: No compression information in table form when performing a Compression test.
  • #1923: No color difference in graph at Compression test
  • #2288: Automated test for EFT
  • #2289: Automated test for Surge
  • #3812: EFT and Surge do not have seperate positive and negative pulse levels
  • #5269: Frequency is not set during harmonic measurement
  • #5285: Harmonics measurement (amplifier cal) is not working
  • #5574: Harmonics measurement could be optimistic
  • #5614: It is possible to start a test without an EUT opened
  • #5737: EFT test duration field is required
  • #5902: Not possible to remove test specific report generator template from items in the report generator settings list
  • #5903: List sorting settings of the Report Generator Settings are not retained
  • #6100: Device driver: Teseq NSG3040
  • #122: Common buttons on the Multiband status test window should be enabled
  • #6129: Device driver: emtest EFT 500M
  • #6132: Sequence number in PI MB EFT test is not updated
  • #6137: Update list of available EFT-line couplings
  • #6138: Update list of available Surge line couplings
  • #6139: Driver: Haefely PEFT-Junior
  • #6140: Selected Cable in EFT & Surge MB test is retained after it doesn't exists anymore
  • #6141: Driver: GPIB support for emtest UCS500N
  • #6144: Update the progress column of the EFT and Surge tests
  • #6145: Implement the test repeat count for EFT and Surge tests
  • #6146: Is Random Surge angle working correctly?
  • #6148: Creating a new EFT MB TSF shows an empty screen
  • #6164: Enable Amplifier harmonics and gain for all users with the Immunity module
  • #6179: Units are not correctly shown initially in the BandsGrid control
  • #6180: Only the duplicates bands should be selected after duplication in the BandsGrid control
  • #6181: Up and down buttons of the BandsGrid control are flickering during changes
  • #6182: Up and Down buttons in the BandsGrid control are swapped
  • #6192: Move the 'Change' button of the units to the bottom right of the units
  • #4354: Test data graph has become black
  • #4398: Graphs (auto) scaling is not functioning as expected
  • #4811: When start frequency is unchanged it's causing frequency range errors
  • #5001: Allow to insert attachments in an EUT file
  • #5002: Possibility to directly attach generated report to the EUT file
  • #5524: File is probably corrupt, or it is created with a newer version of the software
  • #5682: Tolerances of AD Channel are shifted after report generation
  • #6015: Is it possible to perform the power delivery test on another frequency
If you have specific questions regarding on of the above items, please contact us at support@radimation.com

We also include several improvements and new functionalities in version 2015.2.4, the most important improvements are:
  • A lot of crashes/exceptions are resolved.
  • Automated Pulsed Immunity tests (EFT & Surge) are implemented
  • Attaching other data files to an EUT file is now possible
  • Several user interface and usability improvements.
  • Better control of measurement equipment.
The complete list of release notes can be found on: http://wiki.dare.nl/wiki/index.php/Release_Notes_2015.2.

The new 2015.2.4 release of RadiMation can be downloaded from the DARE!! web-site: Image

We always advise to thoroughly test EACH new RadiMation software version to determine if it works correctly in your situation with your equipment, before you use it for daily measurements. This is even a requirement for all ISO 17025 accredited test-labs. To enable customers to validate new software versions before they implement that new software version, we even made it possible to install multiple versions of RadiMation side-by-side on a single PC. This side-by-side installation is normally not possible with other programs but is especially implemented in RadiMation.
Post Reply