New version: RadiMation version 2016.1.10

This forum contains news and upcoming events regarding RadiMation
Post Reply
User avatar
sast
Posts: 168
Joined: 05 Sep 2012, 15:39
Contact:

New version: RadiMation version 2016.1.10

Post by sast »

We have released an updated minor version of RadiMation software, which includes several new device drivers and some small fixes for problems that have been detected since the release of the 2016.1.9 version.
We strongly advise to test and verify (according to your quality system) this and each new version of RadiMation at for example a separate PC or laptop with your setup and with your measurement equipment, before you are going to use it for daily operation.

The following issues are fixed in this 2016.1.10 version (compared to the 2016.1.9 version):
  • #2533: Power conservation is not clearly described in the user-manual
  • #3917: Nonexistent peak and wrong final measurement with PMM during conducted emission multiband tests
  • #4550: Driver: EM-Test Signal generator CWS 500
  • #4596: Problem with PMM in latest version
  • #5989: Driver: emtest CWS500N for IEC61000-4-6
  • #6328: Driver FSV-3 as powermeter
  • #6383: Error -222 Data out of range;INP:ATT 50 DB while deinitializing a R&S ESL 6
  • #6767: Too much reflected power in combination with the RadiField
  • #6955: Error too much reflected power due to RadiField reflected power value
  • #7030: Driver: CWS500N2 EMTEST
  • #7080: Driver: EM test CWS 500N2.2
  • #7232: R&S ESI26: Data out of range: 1 Hz RBW during powermeasurement
  • #7323: Prana MT400 Not all bytes are written to the GPIB-Board within the timeout period
  • #7324: Prana MT400 Amplifier still in operate
  • #7325: Prana MT400 Amplifier not always to RF-ON
  • #7446: Reflected powermeter measurements data is incorrectly shown
  • #7463: Test duration takes a lot of time as compared with a old software used before
  • #7505: Frankonia FC 06 Turntable Error -33072 (Invalid target position)
  • #7508: End frequency is not correctly stored in an attenuation/gain system calibration
  • #7524: Driver NOVOTRONIK GTS5611 switch matrix
  • #7525: Driver NOVOTRONIK GTS5601 switch matrix
  • #7530: Selecting 'AD converter selected in testsite' as monitoring input device is default selecting 'nothing' instead of channel 1 resulting that nothing will be measured
  • #7553: How to configure default graph log or linear scaling?
  • #7554: Driver Advanced settings for ESU 40 as a powermeter
  • #7592: RadiMation does not trigger a GetCurrentStatus after Operate and PowerOff
  • #7599: Driver: AR FL7218 Field Probe
  • #7601: RadiPower RPR2006 powermeter Windows device drivers
  • #7601: RadiPower RPR2006 powermeter Windows device drivers
  • #7602: Bonn Testsystem
  • #7605: GPIB-Board is not controller in charge (CIC) GPIB: ECIC
  • #7607: Shifted Report Generator table
  • #7615: Does the driver of the Power meter E4417E performs reading of the peak value?
  • #7620: PI EFT singleband Report generator codes empty
The complete list of release notes can be found on: http://wiki.dare.nl/wiki/index.php/Release_Notes_2016.1.

The new 2016.1.10 release of RadiMation can be downloaded from the DARE!! web-site: Image

We always advise to thoroughly test EACH new RadiMation software version to determine if it works correctly in your situation with your equipment, before you use it for daily measurements. This is even a requirement for all ISO 17025 accredited test-labs. To enable customers to validate new software versions before they implement that new software version, we even made it possible to install multiple versions of RadiMation side-by-side on a single PC.
Post Reply