New version: RadiMation version 2016.2.7

This forum contains news and upcoming events regarding RadiMation
Post Reply
User avatar
joro
Posts: 440
Joined: 24 Aug 2011, 09:55
Contact:

New version: RadiMation version 2016.2.7

Post by joro »

We have released an updated minor version of RadiMation software, which includes several new device drivers and some small fixes for problems that have been detected since the release of the 2016.2.5 version.
We strongly advise to test and verify (according to your quality system) this and each new version of RadiMation at for example a separate PC or laptop with your setup and with your measurement equipment, before you are going to use it for daily operation.

The following issues are fixed in this 2016.2.7 version (compared to the 2016.2.5 version):
  • #3168: Is amplifier protection working in a multiband immunity test
  • #3517: Radiated Immunity: Level is going too high
  • #4397: Forward power protection file for an Amplifier is ignored if power is already limited
  • #4586: Amplifier limit completely ignored
  • #5099: Too much data point with ESU8 and out of memory errors
  • #5767: ESR7 is an unknown device driver
  • #5952: Error ESRP 3 Receiver DC: More points received from the receiver/analyser then calculated
  • #6853: Decrease testlevel is not available anymore as a shortcut key action
  • #6855: Limitation of a Multiband Immunity test on the current is levelling just above the limit
  • #7459: RadiPower driver doesn't support POWER? in mode 3
  • #7800: Frequency span is not always correctly selected on the Advantest TR4172
  • #7801: Only 51 peaks are detected
  • #3965: Is not possible to choose between EXT-AC and EXT-DC using the siggen HP8648A
  • #5758: Driver Monitor OSD dAV-C(r)-SD/HD
  • #6111: R&S AFG device check seems to be always successful
  • #6557: Update the CD Start menu for 2016.2
  • #7287: Possibility to specify the Attenuation in the generic Powermeter-Analyser device driver
  • #7740: Amplifier Linearity in Net power calibration method
  • #7776: Driver All other ETS-Lindgren 8100-series amplifiers
  • #7805: Deadlock when reviewing a RE Burst test results
  • #7809: emtest CWS500N2.2 powermeters are not correct
  • #7810: HP85xx-series has timeout after DONE query
  • #7813: Clicking Full Span gives error and crash radimation
  • #7815: Rohde & Schwarz ESW8 returns Device not connected
  • #7817: Driver: PMM SB-10
  • #7821: Driver: UCS500Mx
  • #7838: Driver R&S ESR as powermeter
  • #7851: Unknown GetValueID error when using a 1 ohm resistor
  • #7855: Opening older test results triggers errors of wrong correction files
  • #7856: Null reference exception during selection of EUT file, caused by ProposedSaveEUTFilename
  • #7858: Opening older test results shows an error of an incorrect number of columns in the correction file
The complete list of release notes can be found on: http://wiki.dare.nl/wiki/index.php/Release_Notes_2016.2.

The new 2016.2.7 release of RadiMation can be downloaded from the DARE!! web-site: Image

We always advise to thoroughly test EACH new RadiMation software version to determine if it works correctly in your situation with your equipment, before you use it for daily measurements. This is even a requirement for all ISO 17025 accredited test-labs. To enable customers to validate new software versions before they implement that new software version, we even made it possible to install multiple versions of RadiMation side-by-side on a single PC.
Post Reply